S tarting with the pinion gear, insert the shaft into the table bracket and mesh the teeth with the worm gear as shown in. Align the set screw in the crank handle with the flat pad on pinion shaft.
Tighten the 3mm set screw to lock the handle in place see Figure Examine the rack and note that the rack teeth at one end are cut closer to the end of the rack than the other. Insert the rack through the table bracket so the end that has the rack teeth cut closer to the end is pointing down see Figure Hold the rack against the worm gear and slide the table bracket and rack onto the column see Figure Seat the rack tapered-point into the bevel.
Slide the column ring onto the column with the inside bevel in the down position until the rack tapered-point seats into the bevel. Position the column ring so the table bracket and rack can just rotate around the column without binding. Carefully, snug the set screw to hold the column ring in place. Over-tightening the column ring will distort or split the column ring.
The headstock is secured with a set screw so it is aligned with the drill press base for balance and weight distribution. GET help to lift the headstock, or you may seriously hurt your back or drop the headstock. Place the locking gib into the recessed pocket on the inside of the column bracket casting see Figure With an assistant, lift and position the headstock pocket over the column and allow the headstock to slide down until the column fully seats into the headstock.
Rotate the headstock directly over the foot of the base as viewed from the front of the drill press. Screw in the two lock handles on the sides of the headstock. Using a plumb bob and ruler, center the headstock with the base, and tighten the two set screws to secure the headstock to the column see Figure Welcome to ManualMachine.
We have sent a verification link to to complete your registration. Log In Sign Up. Forgot password? Enter your email address and check your inbox. Please check your email for further instructions. Enter a new password. Printed in China. Woodstock Technical Support We stand behind our machines! If you still have questions after reading the latest manual, or if you have comments please contact us at: Woodstock International, Inc.
Attn: Technical Support Department P. Specifications Motor Type V-Belt Drive Bearings JT Swing:. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury and damage to the machine. It may also be used to alert against unsafe practices. Standard Safety Instructions 1. The machine will do a safer and better job at the rate for which it was designed.
Before turning the machine on, make it a habit to check that SAFETY all adjusting keys and wrenches have been removed. When extension cord is feet and less in length, use those that are rated Standard Service grade S or better, and that have a conductor size of 16 AWG. A drop in line voltage, loss of power and overheating can result when using an undersized cord. The extension cord should have a ground wire and ground plug pin, as well. Keep proper footing and balance at all times.
Follow lubrication and accessory attachment instruc- tions in the manual. Dust particles and an ignition source may cause an explosion.
DO NOT operate the machine in high risk areas, including but not limited to, those mentioned above. Additional Safety Instructions for Drill Presses 1. Figure 3. Remove switch safety key when not in use. Extension Cords If you must use an extension cord, use the guidelines below to determine the correct cord length and gauge.
Any electrical outlet and circuit that you plug your machine into must be grounded. Figure 4. Never remove a grounding pin. Immediately discardallplastic bags and packing materials to eliminate a suffocation haz- ard for children and animals. Use the parts list at the back of this manual when ordering parts. Headstock Assembly B. Base C. Column D. Table E. Table Bracket Assembly F. Drill Chuck and Key G. Spindle Handles and Knobs 3 H.
Figure 5. Component inventory. Column Bolts 4 R. W Table Support Arm J. Lift Handle Crank S. Pinion Gear and 5mm M. Lock Handles 4 T. Mounting Hardware N. Rack Refer to the parts list on O. Column Ring Page 30 for details P. Open End Wrench Not shown Q. W Lock Lever. Mark and drill the floor, and install the concrete anchor bolts not included see Figure 6. Figure 6. Secure base to floor. Mounting Holes Figure 8. Workbench mounting holes. Table Support The W comes with a one geared table bracket.
To install the table support assembly, do these steps: 1. S tarting with the pinion gear, insert the shaft into the table bracket and mesh the teeth with the worm gear as shown in Figure 9.
Pinion and worm gear installation. Flat Pad Set Screw Figure Keep work area clean, dry, and welllighted to minimize risk of injury. Only allow trained or properly supervised people to use machine. When machine is not being used, disconnect power, remove switch keys, or lock-out machine to prevent unauthorized use—especially around children.
Make workshop kid proof! Never modify or alter machine for a purpose not intended by the manufacturer or serious injury may result!
Using improper accessories will increase the risk of serious injury. Stop using machine if children or bystanders become a distraction. Verify removal before starting! A secured workpiece protects hands and frees both of them to operate the machine. Feeding in the same direction of rotation may pull your hand into the cut. Make sure they are properly installed, undamaged, and working correctly before using machine. Machine may be damaged. It will do the job safer and better at the rate for which it was designed.
Do not overreach! Avoid awkward hand positions that make workpiece control difficult or increase the risk of accidental injury. Turn machine off and ensure all moving parts completely stop before walking away. An improperly maintained machine may increase the risk of serious injury.
Always repair or replace damaged parts, wires, cords, or plugs before operating machine. Pulling the cord may damage the wires inside. Avoid cord damage by keeping it away from heated surfaces, high traffic areas, harsh chemicals, and wet or damp locations.
Contact our Technical Support for help at Touching a spinning saw blade will cause serious laceration or. Never purposely touch a saw blade during operation.
Never reach around, behind, or over the blade. Operating the saw with the blade guard removed greatly increases the risk of severe laceration or amputation injuries from accidental blade contact. Use the. A through cut is an operation where the blade cuts completely through the top of the workpiece.
Make sure the blade guard is installed and adjusted correctly; promptly repair or replace it if damaged. Always re-install blade guard immediately after operations that require its removal. The riving knife keeps the kerf open behind the blade, which reduces the risk of kickback. A non-through cut is an operation where the blade does not cut. Make sure the riving knife is aligned and positioned correctly; and promptly repair or replace it if damaged.
Using the riving knife incorrectly. Kickback occurs when the saw blade ejects the workpiece back toward the operator. Know how to reduce the risk of. Using or adjusting the fence incorrectly will increase risk of kickback. Make sure the fence remains properly adjusted and parallel with the blade. Always lock the fence in place before operation.
Feeding the workpiece incorrectly will increase risk of kickback. Never start the saw with a workpiece touching the blade; allow the blade to reach full speed before cutting. Only feed the workpiece against the direction of blade rotation. Always use some type of guide fence, miter gauge, sliding table or sled, etc. Never back a workpiece out of a cut or try to move it backwards or sideways after starting a cut.
Feed cuts all the way through to completion. Use push sticks or push blocks whenever possible to keep your hands farther away from the blade while cutting. Never use your hands to move cut-offs away from the blade while the saw is running.
If a cut-off becomes trapped between the blade and table insert, turn the saw OFF and allow the blade to completely stop before removing it. Adjusting the blade height or tilt during operation increases the risk of crashing the blade and sending metal fragments flying with deadly force at the operator or bystanders. Only adjust the blade height and tilt when the saw is turned OFF and the blade is completely stopped.
Never use blades that have been dropped or otherwise damaged. Damaged blades can fly apart and strike the operator with shards of metal. DO NOT attempt dado or rabbeting operations without first reading those sections in this manual. Dado and rabbeting operations require special attention because they must be performed with the blade guard removed.
Kickback is a high speed expulsion of the workpiece from the saw blade, which occurs when the saw blade grabs the workpiece instead of cuts it. Also, kickback can cause serious impact injuries if the operator is struck by the ejected workpiece.
The lack of warning and high risk of injury from kickback makes it extremely important to: 1 avoid doing anything that will increase the risk of occurrence, and 2 work carefully to protect yourself in case it does occur. The workpiece must be able to slide across the table and fence in a stable manner without any rocking, rotating, or shifting—if any of these movements occur during the cut, kickback will likely occur.
Workpieces that have minor warping must be cut with the cupped-side down against the table; the edge of the workpiece that is placed against the fence must be straight or straightened with a jointer. Always use the rip fence or miter gauge to support the workpiece. If the workpiece is not fed parallel with the blade, kickback will likely occur. A misaligned splitter or riving knife can cause the workpiece. If you think that your splitter or riving knife is not aligned with the blade, check it immediately!
Always use the riving knife for all non-through operations, unless a dado blade is installed. Always use the splitter with the blade guard for all through cuts. Anytime you stop feeding a workpiece in the middle of a cut, the chance of kickback is greatly increased. Only remove it when. Remember, always use the riving knife for all non-through operations, unless a dado blade is installed.
Making a deep non-through cut will greatly increase the chance of kickback. If kickback does occur, the thrown workpiece usually travels directly in front of the blade. In the event of kickback, your eyes and face are the most vulnerable part of your body.
Should kickback occur, your hand will be pulled into the blade. If kickback occurs, the push stick will most likely take the damage that your hand would have received.
This machine must be connected to the correct size and type of power supply circuit, or fire or electrical damage may occur. Read through this section to determine if an adequate power supply circuit is available. If a correct circuit is not available, a qualified electrician MUST install one before you can connect the machine to power.
A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the machine. The power supply circuit used for this machine must be sized to safely handle the fullload current drawn from the machine for an extended. If this machine is connected to a circuit protected by fuses, use a time delay fuse marked D. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.
This machine is prewired to operate on a V power supply circuit that has a verified ground and meets the following requirements:. This machine can be converted to operate on a V power supply details about voltage conversion can be found later in this manual.
The V power supply circuit must have a verified ground and meet the requirements that follow:. This machine MUST be grounded.
In the event of certain types of malfunctions or breakdowns, grounding provides a path of least resistance for electric current to travel—in order to reduce the risk of electric shock. Improper connection of the equipment-grounding wire will increase the risk of electric shock. If repair or replacement of the power cord or plug is necessary, do not connect the equipmentgrounding wire to a live current carrying terminal.
Check with a qualified electrician or service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded.
If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one. This machine is equipped with a power cord that has an equipment-grounding wire and NEMA grounding plug. The plug must only be inserted into a matching receptacle see Figure that is properly installed and grounded in accordance with local codes and ordinances.
A NEMA plug has a grounding prong that must be attached to the equipment-grounding wire inside the included power cord. The plug must only be inserted into a matching receptacle see Figure that is properly installed and grounded in accordance with all local codes and ordinances.
We do not recommend using an extension cord with this machine. Extension cords cause voltage drop, which may damage electrical components and shorten motor life.
Voltage drop increases with longer extension cords and the gauge smaller gauge sizes higher gauge numbers indicate smaller sizes. Any extension cord used with this machine must contain a ground wire, match the required plug and receptacle, and meet the following requirements:. The Model is prewired for a V power supply, but it can be rewired to operate on a V power supply.
To reduce the risk of electrocution, machine damage, or an electrical fire, this procedure must be performed by an electrician or qualified service personnel. The procedure involves moving terminal jumpers inside the motor junction box, replacing the machine circuit breaker, and replacing the plug on the power cord.
The require machine circuit breaker can be purchased from an authorized Shop Fox dealer. The required plug and receptacle can be purchased from your local. Open the motor junction box, then loosen the four screws indicated in Figure 4. Remove the two center jumpers they are stacked together , reposition them as shown in Figure 5 , then re-tighten the four screws loosened in Step 2.
Close and secure the motor junction box. Replace the pre-installed 10A circuit breaker see Figure 6 with the 20A circuit breaker, then re-install the switch box. Replace the existing power cord plug with a NEMA plug, according to the instructions and wiring diagram provided by the plug manufacturer. This manual was current at the time of printing. However, if the motor wiring diagram provided on the inside of the junction box cover differs from this manual, always use the junction box cover wiring diagram.
This should reflect any changes that may have occurred after printing. This machine has been carefully packaged for safe transportation. If you notice the machine has been damaged during shipping, please contact your authorized Shop Fox dealer immediately. The following are needed to complete the setup process, but are not included with the machine:.
The Model W is a heavy machine. Serious personal injury may occur if safe moving methods are not used. To be safe, get assistance and use power equipment to move the shipping crate and machine. The following is a description of the main components shipped with the Model W Lay the components out to inventory them.
Occasionally we pre-install certain components for safer shipping. The table and other unpainted parts of your table saw are coated with a waxy grease that protects them from corrosion during shipment.
Clean this grease off with a solvent cleaner or citrus-based degreaser. DO NOT use chlorinebased solvents such as brake parts cleaner or acetone—if you happen to splash some onto a painted surface, you will ruin the finish. Assembly consists of installing minor components, the extension wings and table, fence rails, fence, and blade guard.
Remove the shipping brace shown in Figure 11 , then re-install the fasteners. Save the shipping brace for later machine transport. Thoroughly clean the heavy-duty rust preventative off the gears inside the cabinet and coat them with an appropriate metal protectant refer to Lubrication on Page 55 for the location of gears. The complete and easy-to-read manual makes it easier to assemble and maintain your sander.
Parts and accessories for the planer are available online and shipped from the Woodstock parts warehouse in Springfield, MO. Heavy-duty cast-iron handwheel and table Precision-ground cast-iron infeed and outfeed extension wings Dovetailed way for cutterhead housing with precision gib adjustments Pedestal-mounted controls with variable-speed dial Precision-ground cast-iron table and wings Rubberized steel feed rollers Powder-coated finish One-piece base cabinet View More Details Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Add to Cart Ready to Ship!
Freight Quotes. Additional charges may apply.
0コメント